SR296 VHF/UHF radio modem

SR296  VHF/UHF radio modem

Model No.︰-

Brand Name︰SR

Country of Origin︰China

Minimum Order︰-

Inquire Now

Specifications︰ FEATURES:
¡¤ Clean data each byte of data sent into a SR296 on one end of a link comes out the far end. No dribble bits, no missing header bits. Exactly the same data on each end.
¡¤ Store-and-Forward Repeating The SR296 modem may be programmed to automatically forward transmissions through one or more intermediate stations. This allows SR296 modems to automatically repeat transmissions from units that may be out of range with others in the network, filling in blind-spots and widening the coverage.
¡¤ Distance Synchronous data recovery and intelligent reverse error correction help extend the usable range out to the very fringes of the system.
¡¤ Data Rate Operating at an over the air data rate of 4800 bps, the SR296 Wireless Modem delivers high data rates to the user with a minimum of system overhead. To increase the network efficiency, the serial port may be operated at speeds up to 19200 baud.
¡¤ Synthesized radio frequencies allow easy configuration without the need to install channel crystals. Noise Immunity Radio systems operating near electrical and RF noise sources can benefit from the SR296's error recovery techniques.
¡¤ Asymmetrical Data Rates The data rate of the RS-232 interface on each SR296 unit may be set independently, thus allowing two devices with different data rates to communicate with each other.
¡¤ Data Buffer The SR296 wireless modem comes standard with input and output FIFO data buffers. The FIFO buffers internal to the modem allow communicating devices to send their data at high data rates.
¡¤ Connection Integrity Each byte of data sent between two radios utilizing the SR296 modem is covered by a 16-bit CRC error check, thus ensuring that a byte received on the one end is the same as the one that entered the other end.
¡¤ Built-in RS-232 Interface The serial interface can be configured to use TTL/CMOS levels or RS-232 signal levels. The SR296's serial interface is a standard 9-pin D-subminiature connector. External Programming All features, frequencies, and options in the SR296 may be configured via the RS-232 serial port.
¡¤ Multi-Point Addressing A SR296 wireless modem can be programmed with one of up to 65,536 ID codes. This individual addressing allows them to send and receive data between individual units or "groups" and "subgroups" of SR296 modems.
¡¤ Auto-Transmit The unit automatically keys the transmitter and sends data whenever a presetable number of data bytes is loaded into it's transmit data buffer.
¡¤ Base Station A Base Station version of the SR296 is available. It is similar to the standard modem, except it has special firmware which allows polling of remote units and also identifies the origin of incoming data packets.

SR296 SPECIFICATION

Frequency bands: Standard Bands: 220-240MHz, 450-470 MHz
Special order bands: 218-230MHz, 260-280 MHz, 403-416MHz, 416-430MHz, 430-450MHz, 470-480MHz, 480-496MHz, 496-512MHz
RF power output: 5watts (High power optional - contact factory)
No-tune bandwidth: 10MHz VHF, 20MHz UHF
Maximum duty cycle: 50%, de-rated above 45C to 25% at 60C
Frequency stability: +/-2。5ppm, -30 to +60C
Spurious and harmonic output: <60dBc
Receiver sensitivity -115dbm for 1e-6 ber
Modulation: MSK
Data rate: 25 kHz Channels - 4800bps over the air
Serial Port 300-19200 BPS
PLL step size 12.5kHz
Size: 75 x 112 x 28 mm
Power supply requirements: 12.5V DC,+/-10%.

Export Markets︰ world market

Pricing︰ $150 usd each

Payment Details︰ T/T,prepaid

Min Order︰ 2 pieces

Ship Date︰ within a week